Skip to content
Allot Tech Allot TechChina Manufacturing Programs

Textile procurement guide

Fabric GSM and Grams per Linear Metre Conversion

Compare fabric weight units with a declared width, then verify the actual finished article through measurement.

Fred Textile checked coating fabric illustrating the need to identify weight units and width separately
Procurement planning resource · Allot Tech

Use this guide to prepare a reviewable request. Confirm the selected article or equipment, test basis and responsibilities in the project scope.

Updated October 17, 2026

Direct answer

GSM measures area mass; grams per linear metre also depends on width.

GSM means grams per square metre. Grams per linear metre describes the mass of a one-metre length at a stated fabric width. Convert with g/linear metre = GSM × width in metres, or GSM = g/linear metre ÷ width in metres. The calculation assumes a consistent mass and width basis; it does not measure the fabric, establish tolerance or prove garment performance.

Unit conversion tool

Convert GSM and grams per linear metre.

Use the width corresponding to the stated mass. This browser calculation is unit arithmetic, not a measured fabric result or a shipment acceptance check.

Converted mass—
Width used—

With JavaScript enabled, calculate the selected conversion. Formula: g/linear metre = GSM × width in metres.

Ask what the weight unit and width actually mean.

A quotation headed “weight: 450” is incomplete. Request the unit, whether the value is nominal or measured, the finished article and the width used. GSM and g/m are not interchangeable. A bare g/m label should be clarified as grams per linear metre rather than guessed from a catalogue layout or a photograph.

Use the same width and mass boundary. A whole-width roll mass includes material outside the usable cutting width; dividing that mass by usable width can overstate the GSM of the fabric area being compared. For procurement, record total width, usable width and selvage treatment separately. Request a suitable measured area-mass result when uniformity or contract acceptance matters.

Use the calculation to expose differences in quotation basis.

Illustrative example A: 300 GSM at 150 cm total width gives 300 × 1.50 = 450 g per linear metre. At 140 cm width, fabric with the same 300 GSM gives 420 g per linear metre. The smaller linear mass does not show that the second fabric has a lighter area weight; its area weight is unchanged.

Illustrative example B: 450 g per linear metre at 150 cm corresponds to 300 GSM. The same stated 450 g per linear metre at 140 cm corresponds to about 321.43 GSM. These invented calculation inputs demonstrate units only and are not specifications, prices or available articles from Allot Tech or Fred Textile.

Separate unit conversion from finished-fabric acceptance.

Ask the supplier or laboratory to identify the article and sample, test method and edition, conditioning basis, sampling locations, result and agreed tolerance. Conversion from a nominal linear mass does not replace a test on a defined fabric area. Finishing, moisture condition and variation across a roll can matter when comparing actual measurement results.

GSM alone does not determine warmth, thickness, stiffness, drape or cutting yield. Compare composition, construction, finish, usable width and a physical sample alongside weight. Carry the approved unit and width basis into the purchase specification so a later packing list or inspection report can be checked against the same definition.

The tool supports positive values within its displayed input limits and rounds the displayed result to four decimal places at most. Keep the original supplier values in the comparison record; display rounding is not a production tolerance. Convert centimetres to metres by dividing by 100 before calculating manually.

Problem case: two quotations both say “450”, but the units differ

An illustrative comparison has Quote A at 450 g per linear metre and 150 cm corresponding width, while Quote B states 450 GSM. Quote A converts to 300 GSM, whereas Quote B remains 450 grams per square metre. These are not equivalent weight statements. The example does not imply that either article is better or available: it shows why the unit must be resolved before a procurement comparison.

Now suppose two articles both have 300 GSM, one at 150 cm and one at 140 cm. Their corresponding linear masses are 450 g and 420 g per linear metre. The second figure is lower because one metre of the narrower fabric contains less area. It does not show a lower area mass. Keep this distinction visible when a catalog, quotation and inspection report use different conventions.

Ask the supplier to confirm the actual finished article, mass unit, stated width, treatment of selvages and whether the number is nominal or measured. Preserve the original values and any clarified version. Do not overwrite an ambiguous incoming value with a conversion you guessed. The calculator can check arithmetic only after the mass and width boundaries have been identified.

Problem case: a whole-width weight is divided by usable cutting width

Consider a purely illustrative full-width mass of 450 g per linear metre at a corresponding 150 cm width. It converts to 300 GSM on that declared basis. If someone divides the same full-width mass by 145 cm of usable width, the arithmetic gives about 310.3448, but that does not become a measured area mass of the usable fabric. The mass still includes the original whole-width boundary. This example is a boundary warning, not a test procedure.

To compare the usable fabric itself, request an appropriate measured result under the agreed sample and method, or obtain a mass statement whose boundary genuinely corresponds to the area being evaluated. Keep total width, usable width and selvage information as separate fields. A numerical conversion cannot determine how much material belongs to each boundary or whether the fabric is uniform across its width.

Use the same discipline when a roll weight is supplied. Identify net fabric mass separately from core, wrapping and other packing; also establish actual length and width bases before making an estimate. Even then, a whole-roll inference is not the same record as an identified specimen test. The buyer and checking party should agree which evidence the purchase specification requires.

Build a comparison sheet without implying garment performance

Give each quote an article and revision, supplier, full composition, finish, stated mass/unit, corresponding width, usable width, price/unit and sample reference. Put the calculated conversion in a separate column with the formula and source values. Mark unanswered fields rather than filling them from an attractive photograph or a similarly named article. Where the supplier revises a unit, retain the clarification date and reference.

Only compare price after currency, commercial boundary and width are aligned. The existing usable-area cost tool addresses price per usable square metre, while this tool addresses mass units. Neither selects a garment marker, subtracts defects or proves a shrinkage allowance. A fabric may meet the target GSM and still require decisions about handfeel, structure, finish, seam or interlining behavior.

For approval, attach the physical standard and actual measurement record required by the order. State sample identity, conditioning, method and edition, result and tolerance basis. The displayed rounding of a calculator is not a contractual tolerance. If a development article changes finish, width or construction, review whether the previous weight statement and approval still describe it. This turns a unit question into a controlled specification rather than a number copied between documents.

Keep four fabric quantities separate.

Use consistent units before you compare articles or quotations.

QuantityUnit and meaningWhat else to record
Area massg/m² (GSM): mass per fabric area.Finished article, sampling, conditioning and tolerance.
Linear massg/linear metre: mass of a one-metre length.Width and whether selvages are included.
Roll lengthMetres of fabric along the roll.Measured length method and roll identity.
Area-price comparisonCurrency per usable m².Same currency, usable width and commercial price basis.

Prepare the request

Send the inputs needed to review this requirement.

Article

Code, composition, finish and approved physical sample.

Weight

GSM or g/linear metre, nominal or measured, and agreed tolerance.

Width

Total and usable width with a clear selvage boundary.

Evidence

Sampling and measurement method, conditioning and identified report.

Purchase basis

Price unit, length quantity, development stage and requested delivery.

Reference basis

Primary sources for the technical context.

The checklists are Allot Tech procurement guidance. External manufacturer examples do not establish the capabilities of a quoted Allot Tech configuration.

  • ASTM D3776/D3776M: fabric mass per unit area

    Official standard-family reference for measured fabric area mass. The linked edition is a reference, not a claim that it is the latest or a substitute for the agreed full test method.

Frequently asked questions

Is 450 g/m the same as 450 GSM?

No. If g/m means grams per linear metre, divide by the stated width in metres to obtain the corresponding GSM. Ask the supplier to clarify an ambiguous unit.

Should I use usable width in every conversion?

Use the width corresponding to the stated mass. Do not divide whole-width mass, including selvages, by a smaller usable width and label the result as measured fabric GSM.

Can the calculator verify a fabric shipment?

No. It checks unit arithmetic. Shipment acceptance requires identified samples, agreed measurement methods and the actual article and roll records.

Project discussion

Discuss this fabric requirement

Include the available specifications, samples or files, project stage and destination so the next review can address the actual requirement.

Discuss this fabric requirement